Carrollton Electrical Company handles electrical work for homeowners, landlords, property managers, and businesses across the area. Whether you have a dead outlet that stopped working overnight, a breaker that keeps tripping, or a panel that needs a full upgrade, we scope the job on the call and get it scheduled. We are available around the clock, every day of the week, including nights, weekends, and holidays. When you call us, you get a straight answer about the work. Schedule it. We wire it. You're powered.
Dealing with a tripping breaker or a dead outlet? These are the calls we get most often, and they cover a wide range of causes. A single dead outlet could mean a tripped GFCI somewhere upstream, a loose connection at the device, or a wiring fault in the circuit. A breaker that won't reset after you flip it back usually means the circuit is still overloaded or there is a fault that needs to be found before it will hold.
Flickering lights can point to a loose connection at the fixture, a failing breaker, or a load issue on the circuit. Partial power loss, where half the house goes dark, often traces back to a problem at the service entrance or a failed leg at the panel. These are not situations to leave for later.
A burning smell from an outlet or a sparking panel warrants a call right away. We are available at any hour because electrical faults do not keep business hours. We diagnose the symptom, explain the fault before any work starts, and give you honest recommendations on repairs, never an upsell. Reach out and we'll get it diagnosed.
Wiring is easier to deal with when somebody explains it plainly, and that is how we approach outlet and switch work. Installing a new outlet, replacing a worn device, or adding GFCI protection in a kitchen or bathroom involves more than swapping hardware. We confirm the circuit can carry the load, verify the grounding, and wire everything to code.
AFCI breakers are required in many living spaces under current code, and we handle those installations alongside standard circuit work. Dimmer switches, three-way switch replacements, and smart switch wiring all fall in this category too.
For interior lighting, we install recessed LED fixtures, under-cabinet lighting, pendant lights, and general ceiling fixtures for both residential and commercial spaces. Ceiling fan installation and wiring is part of this work as well. A fan on a circuit that was not designed for one needs the right box and the right wiring before anything goes up. We take pride in the electrical work we leave behind.
This area has every kind of panel and circuit in it, and the same variety shows up in exterior wiring. Outdoor lighting jobs range from a single motion sensor light above a garage door to a full landscape lighting system with multiple circuits, low-voltage runs, and timer controls.
Security lighting for commercial properties and rental buildings often involves higher-output fixtures on dedicated circuits, positioned to cover entry points and parking areas. We run the wiring, mount the fixtures, and confirm the circuit is properly protected.
For residential work, curb appeal and safety both factor in. A well-lit front walk, a backlit driveway, or a lit rear yard all start with the right circuit and the right weatherproof installation. We'll get the job wired and finished.
When the power goes out, or when a panel can no longer keep up with the load a property puts on it, a service upgrade is usually the answer. A 100-amp panel that was sized for a home in a different era is not built for today's appliance loads, EV chargers, or additional circuits. We handle panel replacements and 200-amp service upgrades for residential and commercial properties, including the load calculations that determine what the new panel needs to carry.
Fuse box replacement is common in older Carrollton homes that have not had electrical work done in decades. We replace the fuse panel, bring the service entrance up to current standards, and pull the permits the job requires.
Whole-home rewiring comes up when a property has aluminum wiring from the 1960s or 1970s, knob-and-tube wiring in an older structure, or faulty wiring that has been patched too many times to be reliable. We assess what is there, explain the scope, and give you no-pressure estimates, priced up front. Let us handle the panel and the permits.
A clothes dryer, an electric range, a refrigerator with a high-draw compressor, and a whole-home air handler all need their own dedicated circuits. Sharing a circuit with other devices leads to nuisance tripping at best and a wiring hazard at worst. We run the dedicated circuit, install the correct outlet or disconnect, and confirm the panel has the capacity before the work starts.
For commercial kitchens, retail spaces, and service businesses, dedicated circuit work is often part of a larger project: adding equipment, reconfiguring a space, or bringing an older building up to the load demands of current operations. We handle the circuit installation and any panel work required to support it. We'll find the fault and fix it right.
North Texas puts specific demands on electrical systems. Heavy cooling loads through long summers, rapid residential and commercial growth across Denton County, and a storm season that brings lightning, high winds, and the occasional ice storm all shape what properties here need from their electrical systems.
A four-season climate with extended heat means air conditioning runs hard and long. Older panels that were not sized for that load show it: breakers trip repeatedly, circuits share loads they were not designed for, and adding a new appliance or EV charger pushes the system past its limit. We handle residential 200-amp upgrades and commercial panel work, running load calculations to confirm the new service is sized correctly. Permits are part of the job, and we handle that process as part of the scope.
Severe thunderstorms, tornadoes, and ice storms have knocked out power across the Carrollton area for hours at a time. A standby generator connected through a properly installed transfer switch keeps critical circuits running when the grid goes down. We handle the electrical side of generator hookups: the transfer switch, the dedicated circuit that feeds the generator connection, and the wiring that ties it into the panel. The transfer switch is what makes the system safe, preventing backfeed onto utility lines, and it has to be installed correctly. Call for a quote and we will scope what the installation involves for your property.
A power strip does not protect the rest of the house. When lightning strikes nearby or a utility event sends a voltage spike through the line, a whole-home surge protector at the panel absorbs the surge before it reaches your appliances, smart devices, EV charger, or HVAC equipment. North Texas sees enough storm activity that this is a practical installation, not a luxury add-on. We install whole-home surge protection at the panel, confirm the grounding is solid, and explain what the device covers. Panel upgraded. Circuits balanced. Home powered safely.
Level 2 EV charger installation starts with the circuit. A 240-volt dedicated circuit sized for the charger, run from the panel to the garage or parking area, is what the installation requires. We assess panel capacity first, because adding a 50-amp circuit to a panel that is already near its limit means the panel conversation happens before the charger goes in.
For commercial properties and multi-unit buildings, EV charging in parking areas involves the same circuit work at a larger scale. Multiple charging stations mean multiple dedicated circuits and, in many cases, a subpanel to distribute the load. We scope both residential and commercial EV charger installations and give you a clear picture of what the job involves before anything is scheduled.
This area has every kind of panel and circuit in it, and commercial properties add their own layer of complexity. Offices, retail spaces, restaurants, and light industrial buildings all have electrical demands that go beyond standard residential work. We handle commercial panel upgrades, dedicated circuits for commercial equipment, wiring for tenant improvements, and subpanel installation for spaces that need distributed power.
For landlords and property managers, electrical safety inspections give you a clear picture of what a unit or building contains before a tenant moves in or after one moves out. We check panel condition, wiring, outlets, grounding, and GFCI and AFCI coverage, and we document what we find. We give honest recommendations on repairs, never an upsell, which matters when you are managing a portfolio and need a straight read on what actually requires attention.
An electrical safety inspection covers the panel, the wiring visible in the space, the outlets and switches, grounding and bonding, and whether GFCI and AFCI protection is present where it is required. We note what is working, what is marginal, and what needs attention.
Inspections come up most often at home purchase, before a rental turnover, or when an older property has not had electrical work reviewed in a long time. Knob-and-tube wiring, double-tapped breakers, missing ground wires, and absent GFCI protection in wet locations are the kinds of findings that come out of a thorough inspection. We explain what we find in plain terms so you can make an informed decision about what to address.
How much a job costs depends on what the job involves. A single outlet replacement is a different scope from a panel upgrade with a load calculation and permits. We give you the price on the call, before anything is scheduled, so you know what you are looking at before we arrive.
Panel pricing factors in the size of the new service, whether the meter and service entrance need work, and what permits the job requires. Rewiring cost depends on the size of the property and what is already there. EV charger installation pricing includes the circuit run and any panel work the installation requires. We confirm the scope and the price before work begins. Call for a quote and ask what it covers.
The visit starts with a diagnosis. We identify the fault or confirm the scope of the planned work, explain what we found before any repair begins, and confirm the price if anything has changed from what was discussed on the call. The work is then carried out and tested before we leave.
Most electrical work requires the circuit involved to be de-energized before work begins. For panel work and service upgrades, the main service may need to be shut off for part of the job. We confirm what will be affected on the call so you can plan accordingly.
Yes. The work area should be clear of children and pets for the duration of the visit. Open panels, exposed wiring, and tools in use create hazards that are straightforward to avoid by keeping the area clear. We will let you know which parts of the property are involved before the visit starts.
A warm or discolored faceplate, a burning smell, sparking when something is plugged in, or an outlet that no longer holds a plug securely are all signs the device itself needs to be replaced. A GFCI outlet that will not reset after pressing the button may have failed internally and also needs replacement. These are not situations to leave unaddressed.
A quick repair addresses a specific fault at a device, a connection, or a breaker. A rewire replaces the branch-circuit wiring throughout part or all of a home, typically because the existing wiring is aluminum, knob-and-tube, or has degraded past safe use. The scope is determined by what is found during the diagnosis and explained before any work begins.
Aluminum wiring expands and contracts more than copper under heat, which loosens connections over time and raises the risk of arcing at outlets and fixtures. Homes built in the 1960s and 1970s commonly have it. Remediation requires either replacing the wiring or installing properly rated devices and connectors at every termination point. We assess what is present and explain the options before any work is scoped.
Knob-and-tube wiring lacks a ground conductor and was not designed for modern appliance loads. It is not inherently dangerous if it is in good condition and has not been modified, but it cannot support a grounded system and is often flagged on home inspections. Whether to leave it or replace it depends on its condition and what the property demands. We assess what is there and explain what the findings mean before any work is recommended.
We check the panel condition and age, whether breakers are properly rated for their circuits, whether any breakers are double-tapped or show signs of heat damage, the condition of the bus bars and wiring inside the panel, and whether the service entrance and grounding are in good shape. For a safety inspection, we document what we find and explain it in plain terms.
Additional charges come up when the scope changes once the work is underway. Hidden wiring conditions, a panel that turns out to need more work than was visible from the outside, or a fault that traces back further than the original symptom suggested can all add to the job. We explain what was found and confirm the additional cost before proceeding. No additional work is started until you have agreed to it.
Wiring inside walls, attics, and crawlspaces cannot always be assessed until the work begins. Wiring that has been modified incorrectly in the past, wiring that runs through areas difficult to access, or wiring that turns out to be a different type than expected can all affect the scope. We explain what we found and what it means for the job before any additional work proceeds.
A load calculation is the starting point. We add up the loads the panel is currently carrying and what is being added, confirm the service entrance can support the new panel size, and determine whether the meter or service entrance needs work alongside the panel. The result is a scope that fits the actual demand on the property, not a generic upgrade.
A whole-home surge protector is installed at the main panel and protects every circuit in the home from voltage spikes caused by lightning, utility events, or large motors cycling on and off. We confirm the grounding is solid before installation, because a surge protector depends on a properly grounded system to function correctly. The installation is a single visit and does not require rewiring the house.
Carrollton Electrical Company is available around the clock for electrical repairs, panel upgrades, wiring, and everything in between. We serve Carrollton, Denton County, and the surrounding communities including Farmers Branch, The Colony, Lewisville, Coppell, Flower Mound, and Addison.
Call now. Get it scoped. Get it wired to code.
Reach us any time at (945) 446-2995.
Below is a plain-language look at the electrical work we handle most often in Carrollton and the surrounding area. Each row covers what the service includes, who it fits best, and one practical thing worth knowing before you call. Read through, find what applies to your situation, and call us for a price and a timeline before anything is scheduled.
| Service Type | Scope of Work | Common Situations | What to Keep in Mind |
|---|---|---|---|
| Electrical Panel & Service Upgrades |
| Homes with older 100-amp panels, repeated tripping, or plans to add an EV charger or major appliance | North Texas cooling loads run hard through long summers, and older panels sized for a different era often show the strain before anything else fails. |
| Lighting Installation |
| Residential and commercial spaces adding or upgrading interior or exterior lighting | Outdoor fixtures need weatherproof installation and a properly protected circuit, not just a standard indoor setup. |
| Older-Home Rewiring |
| Owners of Carrollton homes built in the 1960s and 1970s with original or patched wiring | Aluminum wiring expands and contracts under heat more than copper does, which loosens connections over time at outlets and fixtures. |
| Ceiling Fan Installation |
| Homeowners adding ceiling fans to rooms that currently have only a light fixture | A standard light-fixture box is not rated to support a ceiling fan. We confirm the right box is in place before the fan goes up. |
| Electrical Repairs & Troubleshooting |
| Any homeowner or property manager with an active electrical fault | A burning smell or sparking at an outlet warrants a call right away, not a wait-and-see approach. |
| Breaker & Fuse Repair |
| Homes where a circuit repeatedly loses power or a breaker won't hold | A breaker that trips again immediately after reset usually means the fault is still present on the circuit, not in the breaker itself. |
| Whole-Home Surge Protection |
| Any household with sensitive electronics, a home EV charger, or exposure to North Texas storm activity | A power strip only protects what is plugged into it. A panel-level device absorbs a voltage spike before it reaches any circuit in the house. |
| Outlet & Switch Installation |
| Homeowners adding devices, upgrading kitchens or baths, or replacing worn hardware | GFCI protection is required by code in kitchens, bathrooms, garages, and outdoor locations, and we confirm coverage during any outlet job. |
| Dedicated Appliance Circuits |
| Homeowners adding a major appliance or anyone whose breaker trips when a large appliance runs | Sharing a circuit between a high-draw appliance and other devices is a common cause of nuisance tripping and a wiring hazard over time. |
| Backup Generator Installation |
| Homeowners who have lost power during Carrollton-area storms and want critical circuits protected | The transfer switch is the part that makes a generator hookup safe. It prevents backfeed onto utility lines and must be installed correctly. |
| Wiring for Additions & Remodels |
| Homeowners finishing a basement, adding a room, or reconfiguring a commercial space | Remodel wiring often requires a permit and inspection. We handle that process as part of the scope rather than leaving it to the homeowner. |
| EV Charger Installation |
| Homeowners with a new EV and any commercial property adding charging stations for tenants or customers | We check panel capacity before running the circuit. A panel near its limit means the panel conversation happens before the charger goes in. |
What are the signs that a home needs a panel or service upgrade?
The most common signs are breakers that trip repeatedly under normal loads, a panel that runs warm to the touch, breakers that feel loose or do not reset cleanly, and a fuse box that has not been replaced in decades. If you are planning to add an EV charger, a major appliance, or additional circuits and the panel is already near capacity, that is another clear indicator. We run a load calculation to confirm what the property actually needs before recommending a specific panel size.
What causes a breaker to trip repeatedly on the same circuit?
Repeated tripping on the same circuit usually means one of three things: the circuit is carrying more load than it was sized for, there is a wiring fault somewhere on the circuit, or the breaker itself has weakened and is no longer holding its rated load reliably. We diagnose which of those is the cause before replacing anything, because swapping a breaker on an overloaded or faulted circuit does not solve the underlying problem.
Does electrical work in Carrollton require a permit and inspection?
Panel replacements, service upgrades, new circuit installations, and rewiring projects typically require a permit and a code inspection in this area. We handle the permit process as part of the job scope. Work that is permitted and inspected gives you documentation that the installation meets current code, which matters at resale and for insurance purposes.
Faults Traced Before Anything Is Replaced
We diagnose the cause of a fault before recommending a repair. Replacing a breaker on a circuit that is still overloaded or faulted does not fix the problem, and we do not work that way.
When should I call an electrician instead of trying to fix something myself?
Any work that involves the breaker panel, the service entrance, or running new wiring inside walls should be handled by someone who does this work professionally. Replacing a device like an outlet or switch is within reach for a careful homeowner, but a burning smell, sparking, a breaker that will not reset, or partial power loss to part of the house are all situations where the fault needs to be diagnosed before anything is touched. Getting the diagnosis wrong on an active electrical fault carries real risk.
How are emergency electrical calls handled?
We are available around the clock, every day of the week, including nights, weekends, and holidays. If you have an active fault, a burning smell, a sparking panel, or a sudden power loss that is not a utility outage, call us and we will get the situation assessed. We scope the problem on the call so you know what to expect before anyone arrives.
Why do outlets and switches stop working even when the breaker has not tripped?
A dead outlet with no tripped breaker is often a GFCI outlet somewhere upstream on the same circuit that has tripped but not been reset. It can also be a loose connection at the device itself, a failed outlet that has worn out internally, or a wiring fault in the circuit. We trace the cause before replacing anything, because the right fix depends on where the fault actually is.
Permits and Inspection Handled Where Required
Panel replacements, service upgrades, and new circuit work typically require a permit and a code inspection. We handle that process as part of the job scope so you are not left to navigate it on your own.
What do flickering or dimming lights usually mean?
Occasional flickering when a large appliance starts up is usually a load issue on a shared circuit, which a dedicated circuit can resolve. Persistent flickering in one room often points to a loose connection at the fixture or at the breaker feeding that circuit. Flickering throughout the house can indicate a problem at the service entrance or a failing leg at the panel. The pattern matters, so noting when it happens and which lights are affected helps us narrow down the cause on the call.
What is the risk of a warm or buzzing outlet?
A warm outlet faceplate or a buzzing sound at an outlet or switch means there is heat or arcing at the connection behind the device. Both are signs of a wiring problem that needs attention before the device is used again. Arcing at a connection is a fire risk, not a comfort issue. We treat those calls as priority work regardless of the time of day.
Older and Newer Wiring Both Handled
Carrollton homes range from mid-century construction with aluminum or knob-and-tube wiring to recent builds with modern panel configurations. We work with what is there, explain what we find, and scope the job accordingly.
What does an EV charger installation actually require on the electrical side?
A Level 2 home charger needs a 240-volt dedicated circuit, typically a 50-amp circuit run from the panel to the garage or parking area. We start by checking whether the panel has the available capacity for that circuit. If the panel is already near its limit, we address the panel first. For commercial properties or multi-unit buildings, multiple chargers mean multiple dedicated circuits and often a subpanel to distribute the load. We scope the full electrical side of the installation before any work is scheduled.
How do estimates and pricing work when I call?
We give you the price on the call, before anything is scheduled, based on what you describe and what the job involves. For straightforward work like an outlet replacement or a ceiling fan install, that conversation is usually enough to get to a number. For larger jobs like a panel upgrade or a rewire, we confirm the scope and the price before work begins. If something changes once the work is underway, we explain what was found and confirm the cost before proceeding.
How do I know if my home is ready to handle added electrical load?
The panel is the starting point. A panel that is already running close to its rated capacity, that has circuits doubled up on breakers, or that is an older fuse box is not in a position to absorb significant new load without work. We run a load calculation that adds up what is currently on the panel and what is being added, and we confirm whether the service entrance can support the result. That calculation is what determines whether a panel upgrade is part of the project or not.
Call us at (945) 446-2995 any time to get a price, ask about a specific job, or schedule an electrical service call in Carrollton or the surrounding area.
(945) 446-2995